Commonly referred to as a 4th Hand, Park's Cable Stretcher pulls cables tight. Its one-hand operation and thumblock holds the cable so you can easily maintain cable tension while tightening cable fixing bolts and nuts. Made from chrome-plated and heat-treated steel and featuring cushion grips for comfort, the Park Cable Stretcher is a must for any serious mechanic.
The 1729-TA Sliding Thru Axle Adaptor is designed to allow any Park Tool PRS-20, PRS-21 or PRS-23 Repair Stand to accept 12mm and 15mm thru axle wheeled bikes.
Park's Threadless-Fork Saw Guide ensures a straight, accurate cut on threadless carbon forks. Specially designed to accommodate wider, carbon specific saw blades, the SG-8 ensures a perfect cut every time. Slide on the guide, clamp it down and the specially shaped hardened-steel cutting slot guides your saw blade. And, the SG-8 Saw Guide ensures a straight, clean cut on fork steerer tubes up to 1-1/4-inches.
Suspension maintenance and tuning require tools designed for a precise fit. The SKT-6 from Park Tools is a shop-quality set of six flat-faced sockets designed for use with common suspension fork fittings. Ideal for use with Park Tool Torque Wrenches, the 3/8-inch drive sockets are forged from tough chrome vanadium steel and chrome plated for lasting durability. - 24, 26, 27, 28, 30, 32mm flat-faced sockets - All sockets are 3/8" drive - Note: 27mm socket is tapered for better access on Suntour suspension forks
Park Tool's Bottom Bracket Bearing Tool Set removes and installs (with a bearing press which is sold separately) BB86, BB90, BB92 and Press Fit bottom brackets from Shimano, Race Face, SRAM and others that use a nominal 24mm-diameter spindle. This tool has a bearing remover that fits inside the bottom bracket shell and into the bearing so the bearings can be tapped out of the frame with a hammer. The set also includes two bushings that you use in conjunction with a bearing press for precision bearing installation (bearing press sold separately).
Many bicycles will not shift or track properly because the front and rear wheels are not in line with the frame. If these conditions still exist after wheel and derailleur adjustments, the seat stays, chain stays, and rear drop outs of the frame may be misaligned. For years the accepted method to check the alignment of the rear drop-out was to run a string on either side. This method does work to some extent. However, it is not accurate because the measurement is not taken at the drop-out. With the Park Tool Frame Alignment Gauge, the alignment can be checked quickly and accurately at the drop-out. It includes a retractable pointer to fit all sizes and types of bicycles.
Park's Threadless-Fork Saw Guide ensures a straight, accurate cut on threadless forks. Slide on the guide, clamp it down and the hardened-steel cutting slot ensures a perfect cut every time. You can remove as little as 1mm, too.
The HBH-3 securely holds handlebars in place on any bike in any position while in a repair stand. It's useful for brake bleeding, cable and housing routing, lever adjustment, or any scenario where you want to prevent the handlebars from rotating, including storage or working with the bike rotated upwards. With its articulating clamps and adjustable straps, the HBH-3 can easily be attached in a wide variety of positions onto almost any handlebar, seatpost, frame, fork, or repair stand. Anodized aluminum construction with soft rubber straps. - Straps install onto any round tube from 12mm to 60mm (0.5" to 2.4"), as well as most irregular and aero-shaped tubing found on bicycles - Rotating articulating clamps allow for secure installation onto virtually any bicycle in a wide range of positions - Usable extension length of 18" to 32" (45cm to 81cm) - Collapses and folds to 17" (43cm) for storage
Clean out or restore damaged threads in crank arms with Park Tool's Pedal Taps. They're sold as a set of right and left hand threads. Made of high carbon steel, precision ground, and hardened to stay sharp, they cut easily and fit all conventional tap handles. • Includes a set of 2 taps, 9/16" x 20 tpi • Made of high carbon steel, precision ground, and hardened to stay sharp • Fits all conventional tap handles The tap drill size for a 9/16-inch x 20 tpi thread is nominally 33/64-inch.
The Park Tool SBS-1.2 is a shop-quality set of sockets, hex bits, and Torx style bits, selected specifically for common bike repair needs. Ideal for use with Park Tool torque wrenches, the SBS-1.2 3/8" drive bits and sockets are made from tough, chrome vanadium steel for lasting durability.
Truing stand upright extensions install in seconds on any TS-2 or TS-2.2 Truing Stand, allowing the stand to be used on wheels with hubs up to 200mm wide (tandem, fat and downhill bikes), as well as on wheels with a 29-inch mountain bike tire installed*. In addition, specially sized bosses serve as adaptors so the stand can be used with wheels using thru-axle hubs with removable axles. Same features as the the TS-2EXT.2 with the addition of slots to secure rear drive e-bike wheels. * Note: TS-2.2 Truing Stand does not require these adaptors to accommodate 29-inch wheels but does require it to fit hub widths from 180mm to 200+mm.
Park's Freewheel Remover Wrench provides superior leverage for freewheel removal and installation. Its head slides over Park freewheel removers and features a locking knob for a secure fit.
The BBT-30.4 Bottom Bracket Bearing Tool Set is designed and built to install and remove the bearings used in BB30, PressFit 30 (PF30), 386EVO, BBright and PF121 bottom bracket systems. The BBT-30.4 features a bushing set used in conjunction with a head cup press to quickly and precisely press the BB30 and PF30 bearings in the bottom bracket shell. The included BB30 bearing remover works from inside the shell to easily push out bearings.
Secure engagement, easy to use, and fast! The CP-1.2 quickly grips cogs from 9 to 24 teeth with no manual adjustments. A great shop tool, the CP-1.2 is 13.7-inches (35cm) long and can be used with one hand to hold any 5-speed to 12-speed road or mountain cassette solidly during lock ring removal. Forged steel construction with a spring loaded return and comfortable dual density grips.
In the tradition of our premium quality fold up tools, the BO-4 is a combination corkscrew and bottle opener complete with a knife/foil cutter. This multi-tool folds for storage and features all stainless steel mechanisms housed in a forged aluminum case. This is a top quality beverage tool perfect for the workbench, toolbox or wine bar.
This professional-grade set includes five unique cleaning tools purpose-built for scrubbing away dirt and grime, with long ergonomic handles for leverage and comfort. The soaping brush, bottle brush and straight brush feature bristles made from tampico, a natural fiber derived from the agave plant. Tampico is extremely durable, resists chemicals, and holds moisture well, making it an ideal material for cleaning brushes. BCB-5 FEATURES Included brushes: - Soaping Brush: Great for making an initial pass over the bike, dispersing soapy water and breaking up large accumulations of debris. - Tapered Bottle Brush: A general purpose tampico brush for scrubbing areas both big and small. - Straight Brush: A long-reach brush with short, tight tampico bristles for getting into small nooks and crannies such as suspension pivots, saddle rails, and other hard to reach areas. - Drivetrain Brush: Long, stiff nylon bristles make this brush ideal for derailleurs, cassettes, and other areas with grease or dirt build up. - Soaping Sponge: Useful for applying soap and water as well as cleaning delicate surfaces, with a convenient wedge shape. Notes about tampico fibers: - Tampico is a natural fiber: as such, variations in the color of the bristles are to be expected. - Tampico bristles may become temporarily deformed in shipment or storage. Get brushes wet, reshape by hand, and hang to dry. - Always allow tampico brushes to dry fully in an open area before storage to inhibit growth of mildew or mold.
Accurately gauge the straightness of disc brake rotors while the wheel is mounted in a TS-2.2 or TS-2 Professional Wheel Truing Stand (each sold separately). Park Tool's Rotor Truing Gauge features an infinitely adjustable, finely threaded indicator gauge. It works with any diameter brake rotor.
Park Tool's 750.2 Centering Cone Adaptor increases the size of the centering cone of the HTR-1 and HTR-1B Headtube Reaming and Facing Sets. The 750.2 will allow you to use the HTR-1(B) to ream and face head tubes designed to accept IS, ZS, and 1.5-inch EC headset standards. Before reaming or facing, make sure you have the correct cutting tool and pilot for the headset standard(s) you are using. Please refer to our product pages for cutters and pilots for this detailed compatibility information.
A great shop accessory made to hold a wide variety of axles, spindles and any Park Tool Freewheel Remover/Lockring Tool. Made from precision extruded aluminum.
Precision CNC machined dual-sided aluminum tool for the installation and removal of 12- and 36-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8-inch drive. Fits Praxis M30 and M35 - M30: 12-notch 48mm OD cup - M35: 36-notch 51.7mm OD cup
Dial Indicator Set bolts directly to the DT-3 allowing for greater accuracy and a way to measure results. Now includes an elongated, cylindrical tip that is large enough to work around voids in most rotors.
An economical option for safely and accurately tightening fasteners to proper torque specifications. With a simple gauge readout, the TW-2.2 is intuitive and easy to use, and applies up to 60 Nm of torque to any fastener or component with left or right-handed threads. Perfect for mid-to-high-torque applications such as bottom brackets, cassette lockrings, and crank bolts. 3/8" drive for compatibility with all Park Tool sockets, bits, and crow feet, as well as most threaded bottom bracket tools. - 0 to 60 Newton meter (0 to 50 foot-pound) range - 3/8" drive - Reads and registers torque values for both left hand and right hand threading - Length: 17.75" (450 mm)
A fast and convenient tool to remove and install 12-spline Shimano/SRAM style cassette lockrings, as well as similar lockrings on rotor discs. The FR-5H features a modified FR-5 tool that allows use without removing most quick release skewer nuts. The removable, threaded steel handle makes it possible to replace a worn or damaged head. - Fits Shimano, SRAM (including 1x), SunRace, SunTour, Chris King and other cassette lockrings - Also fits some Shimano disc brake lockrings
A dirty drivetrain causes poor shifting and unnecessary wear to expensive parts. The Chain Gang contains everything needed to quickly and easily clean the chain, freewheel cogs, and chainrings. The Chain Gang includes: - CM-5.3 Cyclone Chain Scrubber - GSC-1 GearClean Brush - 8 oz. bottle of Bio ChainBrite The CG-2.4 works on nearly any bike, including multi-speed, single-speed, and e-bikes.
Park’s Professional Cable And Housing Cutter is specifically for use on derailleur and brake cables and housing. It even makes quick work of hard-to-cut shift-cable housing. Its cold-forged, heat-treated-steel handles won't bend and its precision-ground jaws cut perfectly every time. Its dual-density molded grips are specially contoured for superior comfort and control. Plus, there’s a built-in cable-end crimper and a forming hole for reforming housing ends.
Bottom brackets have some of the highest torque specs of any component found on a bicycle. Despite this, some bottom bracket cups feature tool fittings that allow mere millimeters of engagement, which can be a problem when attempting removal or installation. Solution: the Park Tool Bottom Bracket Tool Retaining System. Used in conjunction with nearly any Park Tool bottom bracket tool, the BBT-RS uses a spring-based tension system to apply consistent, adjustable pressure to the tool, ensuring full engagement with the tool fitting and preventing slippage. The BBT-RS can be configured for use with the vast majority of threaded and thread-together bottom bracket standards. The BBT-RS features an M8 threaded rod and a double-sided adapter nut with M12 and M15 threads, allowing it to thread directly into any compatible cartridge bottom bracket. The M15 adapter can also be used to install any of Park Tool's nine aluminum bottom bracket tools, all of which feature integrated threading for use with the BBT-RS. - Washer diameter: 57 mm (2.25") - Rod length: 175 mm (6.9") - Rod threading: M8 x 1.0 - Adapter nut threading: M12 x 1.0 & M15 x 1.0 Compatible with the following bottom bracket styles: - Threaded cup - Thread-together - Cartridge - Cup-and-cone Compatible with the following bottom bracket tools: - The following Park Tool socket-style aluminum bottom bracket tools: - BBT-27.3 - BBT-35-12 - BBT-35-36 - BBT-47-12 - BBT-47-16 - BBT-49.3 - BBT-59.3 - BBT-69.3 - BBT-79.3 - Wrench-style bottom bracket tools with a handle (e.g. Park Tool BBT-9, BBT-29, HCW-4) - Bottom bracket tools with external wrench flats (e.g. Park Tool BBT-19.2, BBT-22)
Shop quality preset torque driver that limit torque applied to fasteners, preventing over tightening and damage to lightweight components. The PTD-4/PTD-5/PTD-6 feature all metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at our factory in Minnesota. - ¼ inch hex drive - Includes 3, 4, 5mm and T25 bits stored in the handle - Limits torque applied to fasteners while rotating clockwise - All metal internal construction for long life
An economical option for safely and accurately tightening fasteners to proper torque specifications. With a simple gauge readout, the TW-1.2 is intuitive and easy to use, and applies up to 14 Nm of torque to any fastener or component with left or right-handed threads. Perfect for low-torque applications such as stem bolts, levers, and carbon fiber components. 3/8" drive for compatibility with all Park Tool sockets, bits, and crow feet. - 0 to 14 Newton meter (0 to 140 inch-pound) range - 3/8" drive - Reads and registers torque values for both left hand and right hand threading - Length: 11.5" (292 mm)
A professional quality shop chain tool that works on 5-speed to 12-speed Road and Mountain Bike derailleur chains*, including SRAM AXS 12 speed, as well as 1/8-inch and 3/16-inch chains. The CT-3.3 features an adjustable locating shelf so it works on any width chain to remove and install chain rivets. Built to last and easy to use, the CT-3.3 features a comfortable handle, investment cast steel body and replaceable driving pin (#CTP). *The CT-3.3 will install, but not peen, Campagnolo 11 and 12-speed chain rivets. - Comfortable T-handle - Replaceable driving pin (CTP) - Investment cast steel body - Adjustable locating shelf
The RT-2 Head Cup Remover makes headset cup removal easy. The tool is pulled through the frame until the flared ends snap in behind the cup. A blow on the tool head removes the cup. • Designed for the 1-1/4 inch and 1-1/2 inch headest standards • Also easily removes cups on one-piece cranks • Strong, heat-treated alloy steel with a nickel finish SHIS Terminology: The RT-2 will remove cups of ZS44, ZS49, ZS55, ZS56, EC49 and EC56 headsets.
Big and powerful, Park's Adjustable Wrench is forged from steel and chrome plated for maximum durability. Its jaws open up to 36mm and the torque-friendly, 12-inch handle is vinyl dipped for comfort.
Keep your work area tidy with Park's Bench Top Small Parts Holder. It's constructed from rugged stainless steel with a clear, acrylic hinged top that lets you see what's inside. It also includes 4 removable bins that are perfectly sized to hold small parts, cable end caps, grease and whatever other little items you can think of.
Park's Professional Pedal Wrench features an angled, oversize head for maximum leverage. It has two 15mm wrenches at different angles, so you can maximize your leverage, and a long, round, vinyl-coated handle that won’t dig into your hand the way flat wrenches do. There's even a hole in the end for hanging the wrench on your toolboard.
Say goodbye to jumbled drawers and crowded bit holders. The JH-3 keeps your bits, sockets, and other tools well-organized and within reach, with three rows of moveable bit holders to fit up to 45 tools with 3/8" drive fittings. Precision-cut openings along the back allow for convenient storage of torque wrenches, drivers, and ratchets. Integrated mounting holes allow for straightforward installation on pegboard or any solid surface. - Assembled dimensions: 14" x 5.8" x 6.2" (356 x 148 x 158 mm) - Mounting holes are 10" (25.4 mm) from center to center - Mounting hardware not included - Durable powder-coated steel construction
The RT-1 Head Cup Remover makes headset cup removal easy. The tool is pulled through the frame until the flared ends snap in behind the cup. A blow on the tool head removes the cup. • Fits 1”, 1-1/8” and 1-1/4” headsets • Strong, heat treated alloy steel with nickel finish The RT-1 will also remove the PressFit 30 (PF30) bottom bracket units. The PressFit 30 inside diameter is the same as headset cups, and are pressed in the same manner. SHIS terminology: Removes cups of EC29, EC30, EC34, EC44, ZS41, and ZS44
$33.95 - $36.95
Precision component screwdriver machined to exact standards to ensure a perfect fit on compatible component fasteners. Featuring an ergonomic, CNC machined and hard anodized 6061 aluminum handle.
Updated to fit current 12-speed cassettes, this combination chain whip and freewheel / lockring remover wrench is heat treated to prevent bending, flexing and wear and features a long, molded handle in addition to a built in hex shaped driver. - Works on 5- to 12-speed road and mountain bike cassettes and freewheels - 1-inch (25.4mm) box-end wrench fits Park Tool Freewheel / Cassette Lockring Tools - Features hardened pins to keep the chain in place
A puncture in your tubeless tire doesn't have to be a death sentence for your ride. This handy carry-along tool repairs small punctures and cuts in tubeless bicycle tires without removing the tire from the rim, getting you back on the trail in no time. The TPT-1 easily plugs the hole by inserting one of the 5 included vulcanized rubber plugs into the puncture. This shrinks the puncture down to a manageable size, allowing the tubeless sealant to do its job and reestablish a seal. The unique sliding plug retainer holds the plug in place and prevents it from being pulled back out as the tool is removed. Everything is stored in a compact package that fits easily in a saddlebag or backpack pocket. - Includes 5 vulcanized rubber plugs (refills available — part #2370K) - Dimensions: 89 x 27 x 40 mm (3.5" x 1.1" x 1.6") - Weight: 79 grams (2.8 oz.) with plugs NOTE: Intended for tubeless bicycle tires using sealant only. Not compatible with inner tube systems.
Professional quality component hex driver precisely machined to exact standards to ensure a perfect fit on compatible component fasteners. Featuring an ergonomic, CNC machined, perfectly balanced 6061 aluminum handle hard anodized to take the rigors of everyday use.
True your wheels right from your bicycle repair stand with Park's Repair Stand-Mounted Wheel-Truing Stand. It's comprised of two parts. One piece is an axle holder for you to securely attach your wheel (accepts all wheel diameters and rim widths) via your quick release or axle nuts. The other piece attaches on the stand near the rim and acts as a pointer that shows where the wheel needs truing. This small, light truing stand installs quickly and easily on Park's PRS-25 and PCS-10 repair stands, and also Park's PCS-1 and PCS-4 stands when they are used with the adjustable-height extension.
The MTB-5 packs 16 functions into one slim, tough folding multi-tool, making it the ideal companion for any trailside adjustment or emergency fix. Features a full set of hex wrenches and screwdrivers, a T25 Torx-compatible driver, and five specialty tools to aid in common on-the-ride repairs. Includes the following: - 2, 2.5, 3, 4, 5, 6 & 8 mm hex wrenches - T25 Torx-compatible driver - Philips #2 cross tip & flat head screwdrivers - Chain tool (5 to 12 speed compatible)* - Spoke wrenches (equivalent to SW-0 and SW-2) - Presta valve core removal tool - Disc brake rotor truing tool - Disc brake pad spreader *The MTB-5 will not peen Campagnolo 11, 12 or 13 speed chain rivets - Dimensions: 3.1" x 1.8" x 0.8" (79 x 45 x 20 mm) - Weight: 6.9 oz. (195 g) - Replaceable chain tool pin (Part #985-1)
The HCW-16.3 is a combination 15mm pedal wrench and chain whip. Use for both pedal removal/installation and for cassette removal. Chain whip features improved compatibility with 5-speed to 12-speed mountain and road bike cassettes and freewheels. The HCW-16.3 is 10.75" long (27.3cm).
Park's I-Beam Mini Fold-Up Hex Wrench/Screwdriver/Torx Set with Chain Tool includes 1.5, 2, 2.5, 3, 4, 5, and 6mm Allen wrenches, a socket 8mm Allen, a regular screwdriver, a T25 Torx tool (for disc-rotor bolts), a tire lever, spoke wrenches and a chain tool. The I-Beam conveniently fits in pockets and packs, too.
This combination chain whip and freewheel / lockring remover wrench is heat treated to prevent bending and flexing, with a molded handle for comfort. - 1/8-inch model works on 1/8-inch chains and sprockets - 1-inch (25.4mm) box-end wrench fits Park Tool Freewheel/Cassette Lockring Tools - Features hardened pins to keep the chain in place
Park Tool's Utility Pick Set is a set of three unique, multi-purpose picks ideal for a wide variety of detail work. Features: • Aluminum handle with magnet • Picks are replaceable, cold formed, heat treated and polished high carbon steel • Set includes 1-straight, 1-hook and 1-90 degree pick
The BK-UK includes six new and revised parts for the Park Tool BKD-1 and BKM-1 Hydraulic Brake Bleed Kits, allowing for compatibility with the latest brake models from popular manufacturers. Includes: - Part #2600A (x2) — M4 x 0.8 adaptor for use with SRAM DB8, Trick Stuff, and Campagnolo mineral oil brake systems - Part #2588.2 — Thin-walled hose compression sleeve for internal bleed nipples, such as those found on Shimano mineral oil brake systems - Part #2574A — Hose assembly with integrated fitting for bleed nipples such as those found on Shimano mineral oil brake systems - Part #2615-2 (x2) — 11 mm bleed blocks for use with Hayes DOT brake systems All parts also available individually. NOTE: The seals on each part are designed for one type of fluid — DOT fluid or mineral oil — and should be used only on the systems they were intended for. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure.
• 15mm L-shaped hex wrench to fit Shimano rear thru-axle freehubs • Through-hardened industrial quality steel • Chamfered tips for a precision fit
The Bottom Bracket Wrench removes and installs Shimano Hollowtech II, Race Face X-type, FSA MegaExo, Campagnolo Ultra-Torque and TruVativ Giga X-pipe bottom brackets. Laser cut for a precise fit, one end of the BBT-9 securely engages the 16 cup notches, while the other end engages the 8 internal splines of the crankarm adjustment cap.
Park's Heavy-Duty Tire Levers handle the toughest tire-and-rim combinations including difficult downhill and freestyle tires. Their specially designed tips engage the tire bead so it can be removed with just two levers. Plus, these beefy, forged-steel levers are a full 8-inches long for superior leverage.
A precision CNC-machined aluminum tool for the installation and removal of select threaded bottom brackets with 16-notch tool fittings, including Wheels Mfg™ Thread Together & FSA® MegaEvo®. Manufactured in-house by Park Tool, anodized for easy identification, and featuring a ratchet/torque wrench-compatible 3/8" drive. Fits 16-notch bottom bracket tool fittings with a major diameter of 48–50 mm and a minor diameter of 46.4 mm, including: - FSA® MegaEvo® - Wheels Mfg™ Thread Together Note: Does not fit Hope™ BSA30
The Park Tool FWS-2 Fold-Up Wrench Set combines all the popular hex and Torx compatible wrench sizes of the AWS-10 and TWS-2 into one convenient set. The multi-position shop grade fold-ups are comfortable, lightweight, slip-resistant, and 40% stronger than steel handles. Made in USA.
Park's Crank and Bottom Bracket Wrench is perfect for working on old-style bottom brackets. The HCW-4 utilizes a 36mm box-end head and a pin spanner for your bottom bracket removal and installation needs.
A great way to keep the benchtop organized during a repair, the OM-2 features an over-sized textured work area and raised trays for organizing small parts and hardware. Perfect for overhauling or rebuilding components such as forks, shocks, hubs, suspension linkages, derailleurs, etc. - Measures 15 x 24.5-inches (38cm x 62cm) - Interlocking edges allow multiple mats to be joined together - Tear/abrasion/shock-resistant TPR construction
$16.95 - $31.95
Professional quality T-Handle hex wrench built for speed, efficiency, leverage and a perfect fit. - Carefully selected combination of Chrome Vanadium and S-2 tool steels - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Machined, chamfered tips allow easier insertion into hex fittings - Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or oversized hexes fast and easy - Sliding T-handle creates increased leverage and multiple access positions
Cleans bicycle chain quickly, easily, and effectively — without the hassle and mess of removing the chain from the bike. The Cyclone uses a large solvent reservoir, hundreds of rotating bristles, and a two-step cleaning process to get chains really clean, improve shifting performance, and extend the life of the chain and other expensive drivetrain parts. - Works with all multi-speed bikes (5, 6, 7, 8, 9, 10, 11, and 12-speed) as well as some single-speed models and e-bikes - Strong magnet at the bottom of the fluid reservoir holds metallic particles scrubbed from the chain - Special wicking sponge draws solvent from the chain as it exits, minimizing drips and mess - Sturdy handle makes the Cyclone easy to use and control - Holds 2 fluid ounces (59ml) of solvent
The 4th edition of the Big Blue Book of Bicycle Repair is updated with the latest information, procedures and techniques and covers everything from minor adjustments to complete overhauls. The BBB-4 features clear, step-by-step instructions, high quality color photos and useful charts and graphs to thoroughly explain and demonstrate hundreds of repairs. Written by one of the world’s leading authorities on bicycle repair and maintenance, Park Tool Director of Education, Calvin Jones, the Big Blue Book is the perfect reference guide for nearly any level mechanic and every bike. New information and topics included in the BBB 4th edition: - 12-speed and 1x drivetrains - Tubeless tires - Disc brakes - Electronic shifting - New wheel building content - Updated headset and bottom bracket standards - Updated torque specifications - Updated troubleshooting tables
A great way to hold small parts, tools and components during a repair, Park Tool's Benchtop Overhaul Mat features multiple small pockets and one large work area. It's perfect for suspension work or to organize parts for installation. • Made of a rubber-like PVC • Cleans easily and looks great on any bench • Measures: 14.7” x 7” (38cm x 18cm)
Your new favorite tool for truing and building wheels. The CSH-1 securely holds spokes in place during spoke tension adjustment to prevent wind-up of round and bladed spokes, as well as rotation of straight-pull spokes. The versatile head can grip spokes in multiple positions for optimal leverage and hand positioning. Constructed of forged heat-treated steel with comfortable dual-density grips. - Compatible with round and bladed spokes 2.3 mm (13 gauge) wide or less - Compatible with J-bend and straight pull spokes
The EP-1 is purpose-built to securely install end caps onto brake, derailleur, and dropper post cables. The short tapered jaws with dual crimping positions make it ideal for crimping in tight, inaccessible spaces. Built from forged machined steel with vinyl-dipped handles.
Shorten your steerer, trim your handlebars and always make sure to measure twice with Park's Hack Saw. It features an outstandingly rigid aluminum die-cast frame with a blade tension adjuster and a superbly comfortable handle. The SAW-1 comes with one blade and accepts all 12-inch (300mm) replacement blades.