$16.99 - $19.99
For the Bluebird chain, Odyssey took the proven and reliable KMC 510-HX chain and added a permanently attached, factory installed half-link to one end. When the chain is trimmed to size you can easily decide whether or not to use the half-link. Original factory assembled pin joints are radically stronger than workshop assembled ones, so this is a huge benefit.
- Sold in pairs. - Allen wrench included.
The 4.5-inch peg features a full 4130 core with a long-lasting, fast-sliding, plastic sleeve. - Sold individually - 14mm with 3/8” adapters only - Replacement sleeves sold separately - 4.5" (length) x 1.5" (outer diameter) - 4.5 oz (9 oz for a pair)
- Lower cables for Odyssey's Gyro G3 (sold separately). - Universal fit. - Lower cables only.
- Upper cables for Odyssey's Gyro G3 (sold separately) - Universal fit. - Upper cables only.
When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.
- 4140 Chromoly - 3 Possible peg positions for longer peg life - 14mm with 3/8-inch adapters included - 4 inches (length) x 1-3/8 inches (outer diameter) - Sold in pairs - 8.75 oz (17.5 oz for a pair)
The Slim by Four is a BMX-specific brake pad with a symmetrical shape designed for both forwards and backwards braking. A custom inner frame helps to stiffen the pad and prevents excessive braking power from being lost to flex. SPECS - Clear and Gum colored “Soft” compound pads provide extra grip on powder coated rims. - Black “Normal” compound Slim-By-Four pads are the most popular pad choice for most riders.
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable. The Springfield brake drops the two ordinary (and confusing) brake springs and replaces them with one central spring that applies the same force to each arm, requiring no additional adjustment. This makes assembly incredibly easy–just bolt it on and go. The brake arms are designed to maximize stiffness and save weight without adding excessive cost. By die-casting the arms and using shared tooling to make each side, the Springfield meets all of the original design goals, resulting in a very powerful and affordable brake.
Odyssey is proud to offer their new tripod post. It allows for the two most popular seat angles amongst riders and it’s clean, light and easy to install. SPECS - 25.4mm diameter - 6061-T6 Aluminium, CNC machined
Broc Raiford can bunnyhop over a house so it’s only right that he has his own grips to hold on to. Broc’s signature grip comes in at 160mm in length and features rope detailing on the ends to tie in with Broc’s nautical theme.
6061 aluminum with precision sealed mechanism bearing and lower (17mm) stack height.
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable too. The Ghost Pad addresses the hassles of brake pad installation by eliminating the traditional dome shaped washers used for toe-in. The pad improves stiffness by building the toe-in into the pad shape and utilizing a solid extruded aluminum frame at its core. The Ghost Pad’s assembly consists of simply lining it up with the rim and tightening down an M6 female bolt. Comes stock on the Springfield brake. SPECS Hardware: - In-bound bolt, 5mm Hex Key, M6x1.0 Thread - Pad Material: Black (standard) or Clear Rubber (Soft) - Weight: 1.0oz / 28g (pair)
Odyssey's original dual cable detangler system has been the industry standard since day one. Odyssey has been making the Gyro since 1986 and constantly improving it along the way. Everything you need to run a Gyro. Odyssey Gyro cables and upper and lower cable stops included.
- Straight gauge spokes with a proprietary grade of stainless steel that is as good or better than the materials used by the world’s most renowned spoke makers. - Sized and dimensioned specifically for BMX.
A total redesign of Odyssey's popular MDS sprocket. With a built-in full guard, this sprocket lives up to its name, helping to protect your chain from anything you can throw at it. Sprocket thickness increases towards the guard area for greater strength. Compatible with all chain widths. - 7075 Aluminum
The Odyssey K-Shield Linear cable features a pre-stretched inner Slic Kable covered in a linear casing to prevent binding and an outer K-Shield mesh housing for less weight over a standard steel mesh housing (2.9 oz). - Black - 60 – 65mm
The M2 lever works with a single cable or Odyssey's dual cable system. - Improved braking power for Gyro users - Left/Right hand compatible
A huge leap forward in pedal technology that results in a simpler overall design. Extremely lightweight plastic bodies eliminate the need for bearings and allow for a spindle that is significantly stronger than normal. Metal pins make the pedal very grippy, and the pedal will still function normally when pins are removed from one side for grind tricks. No flimsy outboard end caps. Pedal body halves are easy and inexpensive to replace – instead of replacing the whole pedal. - 9/16-inch, heat-treated, 4140 chromoly spindle - Proprietary high-strength plastic composite
Odyssey's custom-designed Par Ends come standard with all of their grips. Its special plastic composite will not shatter like cheap bar ends do, and they’re very lightweight. The Par End is a combination of the over-the-bar-style cap and the inside-the-bar-style to prevent the inner portion from blowing out like it does on ordinary press-fit bar ends. Comes stock on all of Odyssey's grips.
It’s a traditional straight up pivotal design with a 200mm length.
New dust cap design, with Monogram laser etched logo, for a cleaner look to accommodate a taller riding set up with less spacers. Same quality as Odyssey's Pro Headset using high-quality sealed bearings and a precision tapered wedge to keep the headset tight at all times. FEATURES - High-quality sealed bearings. - Color matched spacers included. - 15mm dust cap. With 3mm, and 2mm spacers - Laser etched Odyssey bearings. SPECS - Campagnolo standard spec. - 1 1/8-inch integrated headset. - 45º tapered bearings - 41.8mm outer diameter (fits 42mm BMX head tubes).
Designed specifically for use with Odyssey's Quartet FRONT or REAR hubs. SPECS - Forged from 7075-T6 aluminum for greater strength and durability - Steel insert prevents guard deformation, prolonging bearing life
Odyssey took their proven Linear Slic Kable housing and replaced the steel linear wire with aluminum. Utilizing the aluminum wire in the housing saves you significant weight, roughly 30%. This cable also features their specially designed “volcano” ferrules that they’ve used since 2008 to prevent housing blowouts. This Kable also comes with color-coaded inner wires and ball ends to differentiate between their regular Linear’s Race Linear Slic Kable. - Length: 60 – 65mm - Black
- New ultra-slim 2014-T6 aluminum seat clamp with replaceable hardware and self-aligning nut. - 6061-T6 aluminum construction. - Standard 1-1/8-inch size.
Tom likes to ride fast and go very high. These tires were designed to help him do just that. With a fast center tread, these tires are made for park, street and even dirt too. The side profile is reminiscent of a motorcycle tire as well, which is a nod to Tom’s motorcycle lovin’ ways.
$13.99 - $16.99
One of the most successful and popular pedals, and for good reason with its extremely simple, lightweight, inexpensive and famously durable plastic-bodied design. Often duplicated but never replicated. - High-strength plastic composite
Odyssey's 41-Thermal forks quickly established a reputation for strength and quality when they originally introduced them in 1999, and they have since gone on to change the standards that all forks are judged by. The new R-Series forks continue this tradition. FEATURES - Fully redesigned. - Laboratory tested and team proven. - New, custom, seamless, tapered, butted and specially formed leg tube shaping for improved grind and guard clearance. - All-new steerer tube design improves fatigue strength and includes a built-in, integrated, lower headset seat race. - New, optimized, 4mm dropout shape for grind and peg clearance. - Updated 7075-T6 pre-load bolt - Proven 41-Thermal® processed 4130 chromoly - Legendary lifetime replacement warranty SPECS - 25mm traditional offset - 3/8” axle slots only Starting at 1lb 15.2oz (885 grams)
Page 1 of 1